Dremel 4200 (4200-4/75) Spécifications télécharger pdf (Page 18)

Switch Setting Speed Range (/

min)

Qualification

5 5,000

10 10,000

15 15,000

Low speed

20 20,000

25 25,000

30 30,000

33 33,000

High speed

Refer to the Technical Specifications of the

accessory (on-line or on package) for the Maximum

Speed. Do not use high speed when using wire

brushes. At high speed, wires can discharge from

the holder.

1. Use a low speed (15,000 /min or less) when:

a. Polishing, buffing and cleaning with a wire brush.

b. Polishing with felt polishing accessories.

c. Working with materials that can be damaged by

high-speed generated heat. Some materials burn or

melt at low temperatures.

2. Use higher speeds for hardwoods, metals and glass

and for drilling, carving, cutting, routing and shaping.

If a high speed steel cutter starts to vibrate, it usually

indicates that it is running too slow.

3. Aluminium, copper alloys, lead alloys, zinc alloys and

tin may be cut at various speeds, depending on the type

of cutting.

Use a paraffin or other suitable lubricant (not water)

on the cutter to prevent the material from adhering to

the cutter teeth.

MAINTENANCE AND REPAIR

Always unplug the tool from the power source

before you make any adjustments, change

accessories, service, clean, etc. This reduces the

risk of starting the tool accidentally.

Have your power tool serviced by a qualified repair

person who uses only identical replacement parts.

We recommend that all tool service be performed by

a Dremel Service Centre. This will ensure the safety

of the tool. Maintenance performed by unauthorized

personnel can result in incorrect connection of

internal wiring and components which can cause

serious hazard.

You can only inspect and replace the carbon

brushes. There are no other serviceable parts inside

the tool.

CLEANING

1. Clean ventilation openings, switch and levers of the tool

with compressed dry air.

Do not clean the tool by inserting pointed objects

through an opening.

Wear safety goggles to protect your eyes.

2. Clean the surface of the tool with a damp cloth.

Do not clean the tool with cleaning agents and

solvents, such as gasoline, carbon tetrachloride,

chlorinated cleaning solvents, ammonia and

household detergents that contain ammonia. They

can cause damage to the plastic parts.

MAINTAINING THE CARBON BRUSHES

To maintain peak efficiency of the motor, inspect the

brushes for wear every 40-50 hours of use. Also inspect

the brushes when the tool runs erratically, loses power, or

makes unusual noises.

Using the tool with worn brushes will permanently

damage the motor. Use only original Dremel

replacement brushes.

1. Unplug the tool and place it on a clean surface.

2. Remove the two brush caps with the tool wrench as a

screwdriver. Refer to figure 1.

3. Remove the two brushes from the tool by pulling the

springs that are attached. Refer to figure 1.

4. Inspect both brushes. If a brush is less than 3mm

long and/or the surface of the brush is rough or pitted,

replace the carbon brush by a new one.

a. Remove the spring from the brush.

b. Throw away the old brush and place the spring on

a new brush.

If one brush is worn, you should replace both

brushes for better performance of your tool.

5. Place the carbon brushes (with spring) back into the

tool.

There is only one way the brush will fit back into the

tool.

6. Replace the brush caps by turning the caps clockwise.

To tighten, use the wrench, but do not over tighten!

7. Refer to First use to start using the tool again.

SERVICE AND WARRANTY

NO USER SERVICEABLE PARTS INSIDE. This DREMEL

product is guaranteed in accordance with statutory/country-

specific regulations. Damage due to normal wear and

tear, overload, improper handling or lack of reasonable

maintenance and care are excluded from the warranty. In

case of a complaint, send the undismantled tool or charger

and proof of purchase to your dealer.

CONTACT DREMEL

For more information on the Dremel product range, support

and hotline, go to www.dremel.com.

Dremel Europe, P.O. Box 3267, 4800 DG Breda, The

Netherlands

ENVIRONMENT

DISPOSAL

The machine, accessories and packaging should be sorted

for environmental-friendly recycling.

ONLY FOR EC COUNTRIES

Do not dispose of power tools with household

waste! According the European Guideline

2012/19/EC for Waste Electrical and

Electronic Equipment and its implementation

into national law, power tools that are no

longer usable must be collected separately

and disposed of in an environmentally-correct

manner.

GENERAL SPECIFICATIONS

Voltage Rating 230-240 V, 50-60 Hz

Related Power 175 W

Rated Speed (n) 33,000 /min

Collet Capacity 0.8 mm, 1.6 mm, 2.4 mm,

3.2 mm

Class II construction Double insulated

construction tools

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 87 88

Commentaires sur ces manuels

Pas de commentaire

Dremel 4200 (4200-4/75) Spécifications Page 18

Commentaires sur ces manuels

Produits connexes et manuels pour Outils multiples Dremel 4200 (4200-4/75)